1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
|
/**
@Generated PIC24 / dsPIC33 / PIC32MM MCUs Source File
@Company:
Microchip Technology Inc.
@File Name:
system.h
@Summary:
This is the sysetm.h file generated using PIC24 / dsPIC33 / PIC32MM MCUs
@Description:
This header file provides implementations for driver APIs for all modules selected in the GUI.
Generation Information :
Product Revision : PIC24 / dsPIC33 / PIC32MM MCUs - 1.171.4
Device : PIC24FV16KM202
The generated drivers are tested against the following:
Compiler : XC16 v2.10
MPLAB : MPLAB X v6.05
*/
/*
(c) 2020 Microchip Technology Inc. and its subsidiaries. You may use this
software and any derivatives exclusively with Microchip products.
THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER
EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY IMPLIED
WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS FOR A
PARTICULAR PURPOSE, OR ITS INTERACTION WITH MICROCHIP PRODUCTS, COMBINATION
WITH ANY OTHER PRODUCTS, OR USE IN ANY APPLICATION.
IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE,
INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP HAS
BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO THE
FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL CLAIMS IN
ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT OF FEES, IF ANY,
THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS SOFTWARE.
MICROCHIP PROVIDES THIS SOFTWARE CONDITIONALLY UPON YOUR ACCEPTANCE OF THESE
TERMS.
*/
// Configuration bits: selected in the GUI
// FBS
#pragma config BWRP = OFF //Boot Segment Write Protect->Disabled
#pragma config BSS = OFF //Boot segment Protect->No boot program flash segment
// FGS
#pragma config GWRP = OFF //General Segment Write Protect->General segment may be written
#pragma config GCP = OFF //General Segment Code Protect->No Protection
// FOSCSEL
#pragma config FNOSC = PRI //Oscillator Select->Primary Oscillator (XT, HS, EC)
#pragma config SOSCSRC = DIG //SOSC Source Type->Digital Mode for use with external source
#pragma config LPRCSEL = HP //LPRC Oscillator Power and Accuracy->High Power, High Accuracy Mode
#pragma config IESO = OFF //Internal External Switch Over bit->Internal External Switchover mode disabled (Two-speed Start-up disabled)
// FOSC
#pragma config POSCMOD = HS //Primary Oscillator Configuration bits->HS oscillator mode selected
#pragma config OSCIOFNC = IO //CLKO Enable Configuration bit->Port I/O enabled (CLKO disabled)
#pragma config POSCFREQ = HS //Primary Oscillator Frequency Range Configuration bits->Primary oscillator/external clock input frequency greater than 8MHz
#pragma config SOSCSEL = SOSCHP //SOSC Power Selection Configuration bits->Secondary Oscillator configured for high-power operation
#pragma config FCKSM = CSDCMD //Clock Switching and Monitor Selection->Both Clock Switching and Fail-safe Clock Monitor are disabled
// FWDT
#pragma config WDTPS = PS32768 //Watchdog Timer Postscale Select bits->1:32768
#pragma config FWPSA = PR128 //WDT Prescaler bit->WDT prescaler ratio of 1:128
#pragma config FWDTEN = OFF //Watchdog Timer Enable bits->WDT disabled in hardware; SWDTEN bit disabled
#pragma config WINDIS = OFF //Windowed Watchdog Timer Disable bit->Standard WDT selected(windowed WDT disabled)
// FPOR
#pragma config BOREN = BOR3 //Brown-out Reset Enable bits->Brown-out Reset enabled in hardware, SBOREN bit disabled
#pragma config RETCFG = OFF //->Retention regulator is not available
#pragma config PWRTEN = ON //Power-up Timer Enable bit->PWRT enabled
#pragma config I2C1SEL = PRI //Alternate I2C1 Pin Mapping bit->Use Default SCL1/SDA1 Pins For I2C1
#pragma config BORV = V18 //Brown-out Reset Voltage bits->Brown-out Reset set to lowest voltage (1.8V)
#pragma config MCLRE = ON //MCLR Pin Enable bit->RA5 input pin disabled, MCLR pin enabled
// FICD
#pragma config ICS = PGx1 //ICD Pin Placement Select bits->EMUC/EMUD share PGC1/PGD1
#include "pin_manager.h"
#include "clock.h"
#include "system.h"
#include "tmr1.h"
#include "interrupt_manager.h"
#include "traps.h"
#include "mssp1_spi.h"
#include "mssp2_i2c.h"
void SYSTEM_Initialize(void)
{
PIN_MANAGER_Initialize();
CLOCK_Initialize();
INTERRUPT_Initialize();
MSSP2_I2C_Initialize();
MSSP1_SPI_Initialize();
TMR1_Initialize();
}
/**
End of File
*/
|
