1 files changed, 72 insertions, 36 deletions
diff --git a/Arduino/main.c/main.c.ino b/Arduino/main.c/main.c.ino
index 94570bc..ff5d2ee 100644
--- a/Arduino/main.c/main.c.ino
+++ b/Arduino/main.c/main.c.ino
@@ -5,51 +5,87 @@ double P100;
 double load = 0;
 int Q150;
 int Q100;
+
+int amongus = 0;
 void setup() 
 {
-  Wire.begin(0x00);
+  Wire.begin();
   Serial.begin(9600);
-  Serial.println("Enter Nominal System Voltage:");
-  while (Serial.available() == 0){;}
-  VOLTAGE = Serial.parseFloat(SKIP_ALL);
-  Serial.print("System Voltage: ");
-  Serial.println(VOLTAGE, DEC);
-  P150 = (VOLTAGE*VOLTAGE)/150;
-  P100 = (VOLTAGE*VOLTAGE)/100;
-  Serial.println("Enter Load in kW:");
+  //Serial.println("Enter Nominal System Voltage:");
+  //while (Serial.available() == 0){;}
+  //VOLTAGE = Serial.parseFloat(SKIP_ALL);
+  //Serial.print("System Voltage: ");
+  //Serial.println(VOLTAGE, DEC);
+  //P150 = (VOLTAGE*VOLTAGE)/150;
+  //P100 = (VOLTAGE*VOLTAGE)/100;
+  //Serial.println("Enter Load in kW:");
+  
 }
 
 void loop() 
 {
   Serial.flush();
   //while (!Serial.available()){;}
-  double temp = Serial.parseFloat(SKIP_ALL)*1000;
+  //double temp = Serial.parseFloat(SKIP_ALL)*1000;
+  //int temp = Serial.parseInt(SKIP_ALL);
+  //Serial.println(temp, DEC);
+
+//  if((temp != load)&&(temp > 0))
+//  {
+//  load = temp;
+//  if(VOLTAGE <= 500) //We don't want to use the 100ohm resistors if the voltage is higher than 500 as they would draw excessive power. 
+//  {
+//  Q100 = load/P100;
+//  if(Q100 > 5) Q100=5;
+//  Q150 = (load - (Q100*P100))/P150;
+//  }
+//  else
+//  {
+//  Q150 = load/P150;
+//  Q100 = 0;
+//  }
+//  if(Q150 > 15) Q150 = 15;
+//  Serial.print("A combination of ");
+//  Serial.print(Q150, DEC);
+//  Serial.print(" 150ohm and ");
+//  Serial.print(Q100, DEC);
+//  Serial.print(" 100ohm resistors will be activated. ");
+//  //Serial.print(load - ((P150*Q150)+(P100*Q100)),DEC);
+//  Serial.print(((P150*Q150)+(P100*Q100)),DEC);
+//  Serial.println("W Accounted for.");
+//  }
+  
+
+//  delay(25);
+//  Serial.print(amongus, DEC);
+//  Serial.print(" ");
+  Wire.requestFrom(0x30, 1); 
+    while(Wire.available()) {
+        int c = Wire.read();    // Receive a byte as character
+        Serial.println(c);         // Print the character
+    }
+  delay(100);
+//
+  if(amongus > 32)amongus=0;
+//  Wire.beginTransmission(0x30); //Controller Board Has Address 0x07
+////  //Wire.write((Q150 << 3) & Q150);
+//  Wire.write(amongus++);
+//  Wire.write(150);
+//  Wire.endTransmission();
 
-  if((temp != load)&&(temp > 0))
-  {
-  load = temp;
-  if(VOLTAGE <= 500) //We don't want to use the 100ohm resistors if the voltage is higher than 500 as they would draw excessive power. 
-  {
-  Q100 = load/P100;
-  if(Q100 > 5) Q100=5;
-  Q150 = (load - (Q100*P100))/P150;
-  }
-  else
-  {
-  Q150 = load/P150;
-  Q100 = 0;
-  }
-  if(Q150 > 15) Q150 = 15;
-  Serial.print("A combination of ");
-  Serial.print(Q150, DEC);
-  Serial.print(" 150ohm and ");
-  Serial.print(Q100, DEC);
-  Serial.print(" 100ohm resistors will be activated. ");
-  //Serial.print(load - ((P150*Q150)+(P100*Q100)),DEC);
-  Serial.print(((P150*Q150)+(P100*Q100)),DEC);
-  Serial.println("W Accounted for.");
-  }
-  Wire.beginTransmission(0x01); //Controller Board Has Address 0x01
-  Wire.write((Q150 << 3) & Q150);
+  //for(int x = 0; x <32;x++){
+    delay(5);
+    amongus++;
+    //Serial.print("Increment Value");
+    //Serial.println(amongus);
+  Wire.beginTransmission(0x30); //Controller Board Has Address 0x07
+  //Wire.write((Q150 << 3) & Q150);
+  Wire.write(amongus);
+  //Wire.write(amongus);
   Wire.endTransmission();
+  delay(50);
+//  Wire.beginTransmission(0x30); //Controller Board Has Address 0x07
+//  //Wire.write((Q150 << 3) & Q150);
+//  //Wire.write(amongus);
+//  Wire.endTransmission();
 }