1 files changed, 336 insertions, 0 deletions
diff --git a/mcc_generated_files/usb/usb_peripheral/usb_peripheral.h b/mcc_generated_files/usb/usb_peripheral/usb_peripheral.h
new file mode 100644
index 0000000..2957f60
--- /dev/null
+++ b/mcc_generated_files/usb/usb_peripheral/usb_peripheral.h
@@ -0,0 +1,336 @@
+/**
+ * USBPERIPHERAL Peripheral Header File
+ * @file usb_peripheral.h
+ * @defgroup usb_peripheral USB Peripheral Hardware Abstraction Layer (HAL)
+ * @brief Interface for a USB peripheral module that needs to be implemented by a device-specific USB module driver.
+ * @version USB Device Stack HAL Driver Version 1.0.0
+ */
+
+/*
+    (c) 2021 Microchip Technology Inc. and its subsidiaries.
+
+    Subject to your compliance with these terms, you may use Microchip software and any
+    derivatives exclusively with Microchip products. It is your responsibility to comply with third party
+    license terms applicable to your use of third party software (including open source software) that
+    may accompany Microchip software.
+
+    THIS SOFTWARE IS SUPPLIED BY MICROCHIP "AS IS". NO WARRANTIES, WHETHER
+    EXPRESS, IMPLIED OR STATUTORY, APPLY TO THIS SOFTWARE, INCLUDING ANY
+    IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY, AND FITNESS
+    FOR A PARTICULAR PURPOSE.
+
+    IN NO EVENT WILL MICROCHIP BE LIABLE FOR ANY INDIRECT, SPECIAL, PUNITIVE,
+    INCIDENTAL OR CONSEQUENTIAL LOSS, DAMAGE, COST OR EXPENSE OF ANY KIND
+    WHATSOEVER RELATED TO THE SOFTWARE, HOWEVER CAUSED, EVEN IF MICROCHIP
+    HAS BEEN ADVISED OF THE POSSIBILITY OR THE DAMAGES ARE FORESEEABLE. TO
+    THE FULLEST EXTENT ALLOWED BY LAW, MICROCHIP'S TOTAL LIABILITY ON ALL
+    CLAIMS IN ANY WAY RELATED TO THIS SOFTWARE WILL NOT EXCEED THE AMOUNT
+    OF FEES, IF ANY, THAT YOU HAVE PAID DIRECTLY TO MICROCHIP FOR THIS
+    SOFTWARE.
+ */
+
+#ifndef USB_PERIPHERAL_H
+// cppcheck-suppress misra-c2012-2.5
+#define USB_PERIPHERAL_H
+
+#include <stdbool.h>
+#include <stdint.h>
+
+#include <usb_common_elements.h>
+#include <usb_peripheral_endpoint.h>
+#include <usb_peripheral_read_write.h>
+#include <usb_protocol_headers.h>
+
+/**
+ * @ingroup usb_peripheral
+ * @struct USB_CONTROL_TRANSFER_t
+ * @brief The data structure for internally handling control transfers, either IN or OUT.
+ */
+typedef struct USB_CONTROL_TRANSFER_struct
+{
+    uint8_t buffer[64];                                     /**<Default buffer for control data transfers*/
+    volatile USB_CONTROL_STATUS_t status;                   /**<The status of a transfer on this pipe*/
+    uint8_t *transferDataPtr;                               /**<Location in RAM to send or fill during transfer*/
+    uint16_t transferDataSize;                              /**<Number of bytes to transfer to or from RAM location*/
+    uint16_t totalBytesTransferred;                         /**<Number of data transfered last transaction*/
+    USB_SETUP_PROCESS_CALLBACK_t processSetupCallback;      /**<Callback to call during setup process*/
+    USB_SETUP_OVERUNDERRUN_CALLBACK_t overUnderRunCallback; /**<Callback to call on a control overrun or underrun*/
+    USB_SETUP_ENDOFREQUEST_CALLBACK_t endOfRequestCallback; /**<Callback to call when a setup request is complete*/
+    USB_SETUP_REQUEST_t setupRequest;                       /**<Setup request packet*/
+} USB_CONTROL_TRANSFER_t;
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if the Setup event was received.
+ * @param None.
+ * @retval 0 - Setup event was not received
+ * @retval 1 - Setup event was received
+ */
+bool USB_SetupIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if the Start-of-Frame (SOF) event was received.
+ * @param None.
+ * @retval 0 - SOF event was not received
+ * @retval 1 - SOF event was received
+ */
+bool USB_EventSOFIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the SOF event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventSOFClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if the Reset event was received.
+ * @param None.
+ * @retval 1 - Reset event was received
+ * @retval 0 - Reset event was not received
+ */
+bool USB_EventResetIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the Reset event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventResetClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if an Overflow and/or Underflow event was received.
+ * @param None.
+ * @return A value representing the events received
+ */
+uint8_t USB_EventOverUnderflowIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if an Overflow and/or Underflow event was received on the control endpoints.
+ * @param None.
+ * @return A value representing the events received
+ */
+uint8_t USB_ControlOverUnderflowIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the Over/Underflow event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventOverUnderflowClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if a Suspend event was received.
+ * @param None.
+ * @return A boolean value representing the Suspend event received condition
+ * @retval 0 - Suspend event was not received
+ * @retval 1 - Suspend event was received
+ */
+bool USB_EventSuspendIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the Suspend event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventSuspendClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if a Resume event was received.
+ * @param None.
+ * @retval 0 - Resume event was not received
+ * @retval 1 - Resume event was received
+ */
+bool USB_EventResumeIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the Resume event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventResumeClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detects if a Stalled event was received.
+ * @param None.
+ * @retval 0 - Stalled event was not received
+ * @retval 1 - Stalled event was received
+ */
+bool USB_EventStalledIsReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Clears the Stalled event.
+ * @param None.
+ * @return None.
+ */
+void USB_EventStalledClear(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Attaches the device to the USB bus.
+ * @param None.
+ * @return None.
+ */
+void USB_BusAttach(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Detaches the device from the USB bus.
+ * @param None.
+ * @return None.
+ */
+void USB_BusDetach(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Checks if the device is attached to the USB bus not.
+ * @param None.
+ * @retval 0 - USB bus is not attached
+ * @retval 1 - USB bus is attached
+ */
+bool USB_IsBusAttached(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Sets the device address.
+ * @param deviceAddress - Device address to set
+ * @return None.
+ */
+void USB_DeviceAddressConfigure(uint8_t deviceAddress);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Gets the current frame number.
+ * @param None.
+ * @return 15-bit frame number
+ */
+uint16_t USB_FrameNumberGet(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Ensures correct control endpoint initialization.
+ * @param None.
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlEndpointsInit(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Verifies the received control setup.
+ * @param None.
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlSetupReceived(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Handles completed transactions on the control endpoints. Checks and verifies data OUT, data IN, ZLP OUT and ZLP IN.
+ * @param pipe - A combination of endpoint address and direction
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlTransactionComplete(USB_PIPE_t pipe);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Sends ZLP OUT and ZLP IN transactions on the control endpoints.
+ * @param direction - The endpoint direction to send the ZLP
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlTransferZLP(uint8_t direction);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Ensures correct control transfer reset.
+ * @param None.
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlTransferReset(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Updates the transfer data pointer and size in ControlTransfer.
+ * @param *dataPtr - Pointer to new data
+ * @param dataSize - Number of elements in the array
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlTransferDataSet(uint8_t *dataPtr, uint16_t dataSize);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Copies data to the transfer buffer and sets the transfer data pointer and size in ControlTransfer.
+ * @param *dataPtr - Pointer to data to copy
+ * @param dataSize - Number of elements in the array
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlTransferDataWriteBuffer(uint8_t *dataPtr, uint8_t dataSize);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Sets the callback for end of a control request.
+ * @param callback - The function to call for the end of a control request
+ * @return None.
+ */
+void USB_ControlEndOfRequestCallbackRegister(USB_SETUP_ENDOFREQUEST_CALLBACK_t callback);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Sets the callback for the setup processing.
+ * @param callback - The function to call for the setup processing
+ * @return None.
+ */
+void USB_ControlProcessSetupCallbackRegister(USB_SETUP_PROCESS_CALLBACK_t callback);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Sets the callback for a control overrun or underrun.
+ * @param callback - The function to call on a control overrun or underrun
+ * @return None.
+ */
+void USB_ControlOverUnderRunCallbackRegister(USB_SETUP_OVERUNDERRUN_CALLBACK_t callback);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Handles the control Over/Underflow events.
+ * @param overunderflow - A value representing overflow or underflow
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_ControlProcessOverUnderflow(uint8_t overunderflow);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Handles the Stall events.
+ * @param pipe - A combination of endpoint address and direction
+ * @return SUCCESS or an Error code according to RETURN_CODE_t
+ */
+RETURN_CODE_t USB_HandleEventStalled(USB_PIPE_t pipe);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Enables the peripheral and the frame number, enables and resets FIFO, sets the endpoint table address and max endpoints.
+ * @param None.
+ * @return None.
+ */
+void USB_PeripheralInitialize(void);
+
+/**
+ * @ingroup usb_peripheral
+ * @brief Disables the USB peripheral and aborts any ongoing transaction.
+ * @param None.
+ * @return None.
+ */
+void USB_PeripheralDisable(void);
+
+#endif /* USB_PERIPHERAL_H */